Beginner's Plumbing: The Essentials for Installing a Bathtub

Book Appointment Now

How do you actually feel when it comes to A Step-by-Step Guide to Installing a Bathtub?


Installing A Bathtub
Mounting a tub isn't exactly rocket science, but it does require solid plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old tub with a new one is additionally a reasonably challenging job. If the old bathtub is conveniently obtainable, the task can move rapidly; if you need to open a wall surface to get rid of the old tub as well as position the brand-new bath tub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will need a helper to leave the old tub and embeded in the new one. Ensure you have actually qualified yourself for the work as well as are comfortable trying it. Rather than employing a professional to take over a halfway-completed job, it is much better to consider using one prior to you begin. Chances are you might require a specialist plumber to make tube links.
This post will aid you install a brand-new bath tub in your washroom if you have currently gotten a new bathtub as well as don't need to transform the plan of your previous water supply pipes.
Your tools and material list need to comprise the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you need to do is separate the water system. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be fairly problematic because of the restricted accessibility that is often the case.
    Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a fabric prepared for the staying water that will certainly come from the pipes. When the supply pipes have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
    Before going on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and also the other end supplies a link to the existing supply pipes.
    If you need to fit a monobloc, after that you will certainly need reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
    Next off, place the tap in the placing hole in the bath/basin guaranteeing that the washers remain in area in between the tap as well as the sink. Safeguard the tap in place with the maker provided backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet adapters. The previous type needs to be attached to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.

    Mounting the Tub


    Using the two wooden boards under its feet, position the bathtub in the required position. The wood boards are helpful in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small factors.
    The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the level and also changing the feet on the tub till the spirit level checks out degree.
    To install faucets, fit the bottom of the furthest versatile tap port to the ideal supply pipeline by making a compression join; after that do the same for the other tap.
    Switch on the water supply as well as examine all joints and also brand-new pipework for leaks and tighten them if required. Fill the bathtub as well as likewise check the overflow electrical outlet and the typical electrical outlet for leaks.
    Lastly, fix the bath paneling as described in the supplier's instruction manual. Tiling and sealing around the bathtub should wait till the tub has been utilized a minimum of when as this will certainly settle it into its last placement.

    Preparing for the Setup


    Firstly, the supporting framework provided with the bath should be fitted (if needed) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets device to stop stress on the tub.
    Fit the flexible tap adapters to the bottom of the two taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
    Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its last setting.

    Tiling Around the Bathtub


    In the location where the bath satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split a stiff seal, causing the water to permeate the wall between the bathroom as well as the tiling, causing problems with dampness and also feasible leakages to the ceiling below.
    You can choose from a selection of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and also cartridges, and can sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the movement experienced when the tub is in use. The sealant can split fairly very early if you do not think about this activity prior to securing.
    Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily readily available on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or water resistant sticky and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    Do you like reading up on Tools You Need to Install a New Bathtub ? Make a remark down the page. We'd be pleased to hear your suggestions about this post. We hope that you visit us again soon. Sharing is nice. Helping people is fun. I am grateful for your time. Visit again soon.


    Dial, and relax!

    Leave a Reply

    Your email address will not be published. Required fields are marked *